Model 9310 Vehicular Slide Gate OperatorOwner’s Manual DoorKing, Inc.120 Glasgow AvenueInglewood, California 90301 U.S.A. Phone: 310-645-0023Fax:
Instructions regarding intended installation: Install the gate operator only if: 1. The operator is appropriate for the construction of the gate and
For gate operators utilizing contact sensors: 1. One or more contact sensors shall be located where the risk of entrapment or obstruction exist, such
Slide Gate Requirements GateRoadwayPedestrianAccessFenceVehicular GateSidewalkOperatorFenceAll openings of a horizontal slide gate are guarded or scr
Slide Gate Protection FenceOperatorPedestrianAccessFenceSidewalkReverseLoopReverse (Open)LoopOpen Loop(Optional)1112 34Loops to help minimize the pote
Table of Contents Section 1 – Installation 1.1 Specifications ...
Section 5 – Maintenance and Troubleshooting 5.1 Maintenance Schedule...
Page 16 9310-065-H-8-08
SECTION 1 - INSTALLATION Prior to beginning the installation of the slide gate operator, we suggest that you become familiar with the instructions, i
1.2 Concrete Pad The model 9310 vehicular gate operator is designed to be mounted on a concrete pad. 1. Construct a form for the mounting pad acco
1.3 Operator Installation Position the operator on the pad so that there is a minimum clearance of one (1) inch between the back of the operator hous
Page 2 9310-065-H-8-08
1.4 Chain Installation 1. Secure the chain brackets to each end of the gate so that the brackets are level with the top chain cutouts in the operato
1.5 Front Mount Installation 48GROUND LEVELCONCRETE PADREMOVEBREATHERPLUG PIN9310-065-H-8-08 Page 21
1.6 Rear Mount 48GROUND LEVELCONCRETE PADREMOVEBREATHERPLUG PIN Gate BracketsIdler AssemblyP/N 2600-818Page 22 9310-065-H-8-08
1.7 Warning Sign Installation This DoorKing slide gate operator is shipped with two warning signs. The purpose of the warning signs is to alert uninfo
Page 24 9310-065-H-8-08
SECTION 2 – WIRING Before attempting to connect any wiring to the operator, be sure that the circuit breaker in the electrical panel is in the OFF po
2.1 High Voltage Connections Use Table 1 to determine high voltage wire size requirements. The distance shown in the chart is measured in feet from th
2.2 Control Wiring Controls must be far enough from the gate so that the user is prevented from coming in contact with the gate while operating the c
2.3 Loop Detectors Loops and loop detectors must be installed with this gate operator to prevent the gate from accidentally closing on vehicles that m
2.4 Auxiliary Device Wiring 12345678910111213141516 17 184403-010Circuit BoardSecondary EntrapmentProtection InputsDOORKING, INC., INGLEWOOD, CA
Use this manual with the following models only. All 9310 models with circuit board 4403-010. IMPORTANT! The 4403 circuit board used in the model 93
2.5 Primary – Secondary (Bi-parting) Gate Wiring The interface wiring between the two operators requires six (6) wires (18 AWG minimum) for control a
2.6 Terminal Identification and Description 2.6.1 Main Terminal (P1) 1. 24 VOLT COMMON Same as terminal 13. 2. OPEN / RADIO RELAY Functions same
2.6.2 Secondary Device Terminal (P3) External entrapment prevention devices are connected here. 1. OPEN PHOTO-BEAM This input is only active when th
SECTION 3 - ADJUSTMENTS The switch settings and adjustments in this chapter should be made after your installation and wiring to the operator(s) is c
3.2 Switch Settings The two DIP-switches located on the circuit board are used to program the operator to operate in various modes and to turn on or o
3.2.1 Programming Switch Description and Function 8-DIP (Top) Switch Switch 1: Set so that the operator cycles open upon initial power up and open co
3.3 Limit Switch Adjustments 1. Be sure that power to the operator is OFF. 2. Push the gate to the open position. Adjust the OPEN limit nut so tha
3.4 Reverse Sensitivity Adjustment This vehicular gate operator is equipped with an inherent (Type A) entrapment sensing system. This system will sens
Page 38 9310-065-H-8-08
SECTION 4 – OPERATING INSTRUCTIONS WARNING - To reduce the risk of injury or death: 1. READ AND FOLLOW ALL INSTRUCTIONS. 2. Never let children ope
Mount operator to pad using 3/8 or 1/2 sleeve anchors.See page 18-19.12Attach chain. Adjust chain to allow approximately 1-inch of sag per 10-feet of
4.2 Shutdown Conditions Under various entrapment conditions the operator will assume either a soft or hard shutdown (alarm) condition. To determine w
4.2.3 Hard Shutdown A hard shutdown condition occurs when the inherent entrapment protection system has sensed two consecutive obstructions before the
4.3 Manual Gate Operation This operator is equipped with a manual release system that will allow the gate to be pushed open in the event of a power ou
4.3.3 Fail-Secure Manual Operation The FAIL-SECURE option locks the gate when primary (AC) power is removed and requires a keyed release to place the
Page 44 9310-065-H-8-08
SECTION 5 – MAINTENANCE AND TROUBLESHOOTING Inspection and service of this gate operator by a qualified technician should be performed anytime a malf
5.2 Operator Diagnostics This gate operator is designed with built-in diagnostics that will alert you to potential or existing problems that the micro
5.3 Trouble Shooting Have a good VOM meter to check voltages and continuity. A Meg-Ohm meter capable of checking up to 500 meg-ohms of resistance is
Gate opens a short distance, then stops and reverses. • Disconnect the gate from the gate operator and check that the gate slides freely without an
5.4 Accessories The following accessory items can be used with the model 9310 slide gate operator. Contact Sensor Contact sensors for use as a sec
94109410EXIT LOOPREVERSE LOOPON1231 DIRECTION2 TIMER1 Open Cycle Photocell2 Close Cycle Photocell3 Open Cycle Contact Sensor4 Close Cycle Contac
Title:Date: Rev.Dwg. No.DOORKING, INC., INGLEWOOD, CA 903011 2 3 4 5N.O.N.C.COMN.O.N.C.COMWhiteRedYellowBlueLimit LimitPartial LimitP2 P112345678910
Title:Date: Rev.Dwg. No.DOORKING, INC., INGLEWOOD, CA 903011 2 3 4 5N.O.N.C.COMN.O.N.C.COMWhiteRedYellowBlueLimit LimitPartial LimitP2 P112345678910
Title:Date: Rev.Dwg. No.DOORKING, INC., INGLEWOOD, CA 903011 2 3 4 5N.O.N.C.COMN.O.N.C.COMWhiteRedYellowBlueLimit LimitPartial LimitP2 P112345678910
Title:Date: Rev.Dwg. No.DOORKING, INC., INGLEWOOD, CA 903011 2 3 4 5N.O.N.C.COMN.O.N.C.COMWhiteRedYellowBlueLimit LimitPartial LimitP2 P112345678910
Title:Date: Rev.Dwg. No.DOORKING, INC., INGLEWOOD, CA 903011 2 3 4 5N.O.N.C.COMN.O.N.C.COMWhiteRedYellowBlueLimit LimitPartial LimitP2 P112345678910
9310-065-H-8-08 Page 55
Glossary GATE: A moving barrier such as a swinging, sliding, raising, lowering, or the like, barrier, that is a stand-alone passage barrier or is tha
Entrapment Protection Protection Against Entrapment Gate Operator Category Horizontal Slide, Vertical Lift, Vertical Pivot Swing and Vertical Barrier
Important Notices Vehicular gate operator products provide convenience and security. However, gate operators must use high levels of force to move gat
Important Safety Instructions WARNING - To reduce the risk of injury or death: 1. READ AND FOLLOW ALL INSTRUCTIONS. 2. Never let children operate o
Comments to this Manuals