DoorKing 6003 Owner's Manual download pdf

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

CAUTION

7”

RED 24V RED

BLK 115V WHT

QUICKSTART “BASIC” GUIDELINES FOR MODEL 115 VAC 6003 - FOR A GATE UP TO 10 FEET, 300LBS AND “OPENING TO THE INSIDE”

120 Glasgow Avenue

Inglewood, California 90301

U.S.A.

115 VAC Connection

Battery Connection

40.5” Fixed Position

Mounting System and Adjusting Open/Close Position

90°

A support

bar must be

installed the

entire length

of the gate

to support

the pickets.

Securely mount control box

near the actuator arm with

appropriate hardware

(not supplied).

Gate Hinge Pivot Point

1. Brown

2. Blue

3. Orange

4. Red

5. Yellow

6. Green

7. Green/White

Actuator

Cable

Loop Wires

Coaxial Cable Antenna

(Not Supplied)

Coaxial

Cable

Antenna

Actuator

Cable

Power Conduit

Loops Conduit

Alarm

Reset

Com

4 Open Input

5 Open Input

N.O.

Relay

24V

Chassis

Ground

Mounting

Hole

Front Bracket Pivot Point

Front Bracket

Rear Bracket

(Adjustable, See Manual)

Rear Bracket Pivot Point

Radio Receiver

Tip: It is recommended

that a surge suppressor

be installed on the high

voltage power lines.

Manual Key Release

Not included - Refer to the Wiring/Owner’s

manual and Loop Information Manual

(available free from www.dkaccess.com) for

more information.

Do not connect the battery to the circuit

board until power is needed to test the

actuator arm.

KEY SWITCH BUTTON: Cycles operator when pressed.

RESET BUTTON: Resets circuit board.

Closed Position

Open to

the Inside

Position

Control Box

Actuator arm and brackets MUST be level!

CONTROL BOX MUST BE

PROPERLY GROUNDED!!

6003-066-L-1-13

OPEN

Mounting Holes

9410

9409

4302

12 V

3 Amp/Hr

Battery

12 V

3 Amp/Hr

Battery

Limit

Slow Down

Unscrew 4 screws to remove cover.

Loosen nut to adjust limit sensor.

Note: To turn-off ALL power to the operator, the AC

power switch must be turned off and the battery

plug must be disconnected from the circuit board.

Note: This illustration shows

NO gate hinge inset. If gate

hinge is inset on wall, see

“Rear Bracket Configurations

for Different Gate Hinge Insets”

in the Actuator Arm and Control

Box Mounting manual.

Limit Sensors

Circuit board power

must be on to adjust

limit sensors, LEDs

will light.

123

1. Direction Primary operator opens.

2. OFF

3. OFF

4. ON Auto-Close Timer

5. ON - Shadow Loop

6. OFF

7. OFF

8. OFF

Adjust 1 to 23 sec.

Cut Off Excess Bracket

Bottom

Middle

Top

Coaxial Cable Antenna Kit

P/N 1514-073 (Sold separately)

1. ON - Relay for Dual Plug-In Shadow Loop

2. OFF - Relay for Dual Plug-In Shadow Loop

3. OFF

4. OFF

SW 1

2 3 4 5 6 7 8

SW 2

2 3 4

Typical Settings for Single Operator with Plug-In Loops

Plug-In Loop Detectors

Circuit Board Settings

Single Channel Exit

Plug-In Loop Detector

Dual Channel

Reverse and Shadow

Plug-In Loop Detector

Battery Plug

AC Power Switch

Relay must be set

to N.O. for shadow

loop.

Loop

Jumper

To #11

To #8

DANGER

HIGH VOLTAGE!

White - Neutral

Black - 115 VAC Hot

Green - Chassis Ground

Low Voltage

Tip: Never run low voltage

rated wire insulation in the

same conduit as high voltage

rated wire insulation. Keep

them in separate conduits.

High Voltage

Wire Size Distance

14 AWG

12 AWG

Up to 200 ft

Beyond 200 ft

115 VAC Input

Power Wire

#8 - #11 Shadow Loop Output

DO NOT cycle operator before limit sensors

and DIP-switches have been adjusted,

damage could occur to gate and operator.

Please refer to the Wiring/Owner’s manual.

Model 115 VAC 6003 is intended for installation only on swing gates used for vehicles.

Pedestrians must be supplied with a separate access opening. For safety and installation instructions, please refer to the

6003 Actuator Arm and Control Box Mounting manual and the 115 VAC Control Box Wiring/Owner’s manual.

SINGLE/PRIMARY

Actuator Cable

Circuit Board

Connection

DO NOT connect the

Primary operator to

this connection.

Connect Secondary

operator ONLY.

Do not install the actuator arm in

fully extended (Bottomed out)

position. This will damage the arm

(See Actuator Arm and Control

Box Mounting manual for more

information).

See reverse side.

Note: Please refer to the

Wiring/Owner’s manual for

more information.

Not included - Refer to a specific Radio

Receiver Manual (available from

www.dkaccess.com) for more information on

radio receivers and antenna installation. See

reverse side for wiring.

3 Limit

5 Limit

4 Slo Dwn

6 Slo Dwn

1 2

Summary of Contents

Page 1 - HIGH VOLTAGE!

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 CAUTION7”7”RED 24V REDBLK 115V WHT QUICKSTART “BASIC” GUIDELINES FOR MODEL 11

Page 2 - Main Terminal

OFFOpeningDirection ofSECONDARYOperator23Terminal #4 is output from plug-in exit loop detector installed in EXIT loop port.Same opening directions as

DoorKing 6003 Owner's Manual

Browse online or download Owner's Manual for Gate Opener DoorKing 6003. DoorKing 6003 Owner`s manual [en] User Manual

Summary of Contents

More documents for Gate Opener DoorKing 6003

Comments to this Manuals

DoorKing 6003 Owner's Manual

Browse online or download Owner's Manual for Gate Opener DoorKing 6003. DoorKing 6003 Owner`s manual [en] User Manual

Summary of Contents

More documents for Gate Opener DoorKing 6003

Comments to this Manuals

Related products and manuals for Gate Opener DoorKing 6003